|本期目录/Table of Contents|

[1]罗马亚,陈常连*,黄小雨,等.氮化硅结合碳化硅多孔陶瓷支撑体的制备与表征[J].武汉工程大学学报,2016,38(05):452-457.[doi:10. 3969/j. issn. 1674?2869. 2016. 05. 008]
　LUO Maya,CHEN Changlian*,HUANG Xiaoyu,et al.Preparation and Characterization of Porous Ceramic Supports of Silicon Nitride-Bonded Silicon Carbide[J].Journal of Wuhan Institute of Technology,2016,38(05):452-457.[doi:10. 3969/j. issn. 1674?2869. 2016. 05. 008]
点击复制

氮化硅结合碳化硅多孔陶瓷支撑体的制备与表征(/HTML)
分享到：

《武汉工程大学学报》[ISSN:1674-2869/CN:42-1779/TQ]

卷:
38
期数:
2016年05期
页码:
452-457
栏目:
材料科学与工程
出版日期:
2016-11-02

文章信息/Info

Title:
Preparation and Characterization of Porous Ceramic Supports of Silicon Nitride-Bonded Silicon Carbide
作者:
罗马亚; 陈常连*; 黄小雨; 王璀璨; 叶旭辉; 黄志良; 张占辉
武汉工程大学材料科学与工程学院，湖北 武汉 430074
Author(s):
LUO Maya;  CHEN Changlian*;  HUANG Xiaoyu;  WANG Cuican;  YE Xuhui;  HUANG Zhiliang;  ZHANG Zhanhui
School of Materials Science and Engineering, Wuhan Institute of Technology, Wuhan 430074, China
关键词:
碳化硅; 氮化硅; 孔隙率; 抗折强度; 孔径分布
Keywords:
silicon carbon;  silicon nitride;  porosity;  flexural strength;  pore size distribution
分类号:
TB321
DOI:
10. 3969/j. issn. 1674?2869. 2016. 05. 008
文献标志码:
A
摘要:
以碳化硅、硅粉为主要原料，以氧化铝和氧化钇为烧结助剂，通过添加不同质量分数的淀粉为造孔剂，采用反应烧结方式制备了系列氮化硅结合碳化硅多孔陶瓷支撑体，并对烧成样品的物相、显微结构、孔隙率、抗折强度、孔径分布、纯水通量和耐酸碱性能进行了分析和表征. 结果表明，样品的主晶相为碳化硅和氮化硅，还有少量的焦硅酸钇和塞隆；随着淀粉质量分数的增加，样品的孔隙率随之增大，样品的抗折强度随之减小，同时样品的平均孔径和纯水通量随淀粉质量分数的增加均呈现先增大后减小的趋势；样品有良好的耐酸碱性能，在标准酸性和碱性条件下的质量损失率分别为1.96%~2.04%、3.96%~4.13%；当淀粉的质量分数为3%时，烧成样品的孔隙率为41.8%，抗折强度为18.1 MPa，孔径主要分布在0.7 μm~2.5 μm之间，纯水通量最高，可达9.2 m3/（m2*h），综合性能较佳.
Abstract:
A series of porous ceramic supports of silicon nitride-bonded silicon carbide （SNBSC） were prepared by reactive sintering, using silicon carbon powder and silicon powder as raw materials, alumina and yttrium oxide as sintering additives and different mass fractions of starch as pore-forming agent. The crystal phase, microstructure, porosity, flexural strength, pore size distribution and acid and alkali resistance of the samples were characterized. The results show that the main crystal phases of the samples are silicon carbide and silicon nitride, and the minor phases are yttrium pyrosilicate and sialon. The porosity of the samples increases while the flexural strength decreases with the mass fraction of starch increasing, respectively. Simultaneously, the mean pore diameter and the pure water flux of the samples both increase and then decrease with the increase of the mass fraction of starch. The porous ceramic supports of SNBSC exhibit good acid and alkali resistance, and the mass loss rates are 1.96%-2.04% in standard acidic conditions and 3.95%-4.13% in standard alkaline conditions, respectively. They also show better comprehensive properties with porosity of 41.8%, flexural strength of 18.1 MPa, pore diameters in the range of 0.7 μm and 2.5 μm, and the maximum value of pure water flux of 9.2 m3/（m2*h） when the mass fraction of the starch is 3%.

参考文献/References:

［1］　孟广耀， 陈初升， 刘卫，等. 陶瓷膜分离技术发展30年回顾与展望［J］. 膜科学与技术， 2011， 31（3）：86-95. MENG G Y， CHEN C S， LIU W， et al. Ceramic membrane technology：30 years retrospect and prospect［J］. Membrane science and technology， 2011， 31（3）：86-95. ［2］　CHEN S T J， YANG J M. Quantitative determination of the stability of SiC whisker in reaction-bonded/hot-pressed Si3N4 composites by X-ray diffraction［J］. Journal of materials science， 1992， 28（19）：5123- 5132. ［3］　WANG C M， PAN X Q， R?HLE M， et al. Silicon nitride crystal structure and observations of lattice defects［J］. Journal of materials science， 1996， 31（20）：5281- 5298. ［4］　ROCHA I C C， MARQUES J J， SILVA A S. Effects of ultrasound on the performance improvement of wastewater microfiltration through a porous ceramic filter［J］. Brazilian journal of chemical engineering， 2009， 26（4）：641-648. ［5］　JO Y M，HUCHISON R，RAPER J A. Preparation of ceramic membrane filters， from waste fly ash， suitable for hot gas cleaning［J］. Waste management & research， 1996， 14（3）：281-295. ［6］　JING Y， DENG X， LI J， et al. Fabrication and properties of SiC/mullite composite porous ceramics［J］. Ceramics international， 2014， 40（1）：1329- 1334. ［7］　HU H L， ZENG Y P， XIA Y F， et al. Rapid fabrication of porous Si3N4 /SiC ceramics via nitridation of silicon powder with ZrO2 as catalyst［J］. Ceramics international， 2014， 40（5）：7579-7582. ［8］　饶安平， 桂明玺. 采用陶瓷过滤器的高温烟气处理技术［J］. 国外耐火材料， 2003，28（ 6）： 22-26. ［9］　李俊峰， 林红， 李建保. 碳化硅多孔陶瓷气孔率和强度影响因素［J］. 无机材料学报， 2011， 26（9）： 944-948. LI J F， LIN H， LI J B. Influence factors on the porosity and strength of SiC porous ceramic［J］. Journal of inorganic materials， 2011， 26（9）： 944-948. ［10］　PRABHAKARAN K， MELKERI A， GOKHALE N M， et al. Preparation of macroporous alumina ceramics using wheat particles as gelling and pore forming agent［J］. Ceramics international， 2007， 33（1）：77-81. ［11］　姜洪舟. 无机非金属材料热工设备［M］. 武汉：武汉理工大学出版社， 2012：532. ［12］　李忠全. 气泡法测定多孔材料的中流量孔径［J］. 粉末冶金工业， 1996，6（6）：14-18. LI Z Q. Determinging mean-flow pore size of porous material with gas bubble method［J］. Powder metallurgy industry， 1996，6（6）：14-18.

相似文献/References:

[1]徐　慢,王　亮,祝　云,等.多孔大通量莫来石相碳化硅陶瓷的制备与表征[J].武汉工程大学学报,2015,37(02):15.[doi:10. 3969/j. issn. 1674-2869. 2015. 02. 00４]
　,,et al.Ｆａｂｒｉｃａｔｉｏｎ ａｎｄ ｃｈａｒａｃｔｅｒｉｚａｔｉｏｎ ｏｆ ｂｉｇ ｆｌｕｘ ａｎｄ ｐｏｒｏｕｓ ｍｕｌｌｉｔｅ ｐｈａｓｅ ｏｆ ｓｉｌｉｃｏｎ ｃａｒｂｉｄｅ ｃｅｒａｍｉｃ[J].Journal of Wuhan Institute of Technology,2015,37(05):15.[doi:10. 3969/j. issn. 1674-2869. 2015. 02. 00４]
[2]安子博,汪　晗,竺昌海,等.硅碳直接反应法制备超细β-SiC粉[J].武汉工程大学学报,2016,38(06):560.[doi:10. 3969/j. issn. 1674?2869. 2016. 06. 009]
　AN Zibo,WANG Han,ZHU Changhai,et al.Preparation of Ultrafine-SiC Powder by Direct Reaction of Silicon and Carbon[J].Journal of Wuhan Institute of Technology,2016,38(05):560.[doi:10. 3969/j. issn. 1674?2869. 2016. 06. 009]
[3]袁　密,高　峰,竺昌海,等.磷掺杂碳化硅的制备及其影响因素[J].武汉工程大学学报,2018,40(05):538.[doi:10. 3969/j. issn. 1674-2869. 2018. 05. 012]
　YUAN Mi,GAO Feng,ZHU Changhai,et al.Preparation of Phosphorus Doped-Silicon Carbide and Influence Factors[J].Journal of Wuhan Institute of Technology,2018,40(05):538.[doi:10. 3969/j. issn. 1674-2869. 2018. 05. 012]
[4]周诗聪,陈常连*,梁　欣,等.不同粒径碳化硅粉体的复合烧结与表征[J].武汉工程大学学报,2020,42(03):298.[doi:10.19843/j.cnki.CN42-1779/TQ.201905018]
　ZHOU Shicong,CHEN Changlian*,LIANG Xin,et al.Composite Sintering and Characterization of SiC Powders with Different Particle Sizes[J].Journal of Wuhan Institute of Technology,2020,42(05):298.[doi:10.19843/j.cnki.CN42-1779/TQ.201905018]
[5]梁　欣,陈常连*,周诗聪,等.碳化硅添加对氮化硅转化为碳化硅晶粒形貌的影响[J].武汉工程大学学报,2019,(01):60.[doi:10. 3969/j. issn. 1674?2869. 2019. 01. 009]
　LIANG Xin,CHEN Changlian*,ZHOU Shicong,et al.Effect of Addition of Silicon Carbide on Morphology of Silicon Carbide Grains Transformed from Silicon Nitride[J].Journal of Wuhan Institute of Technology,2019,(05):60.[doi:10. 3969/j. issn. 1674?2869. 2019. 01. 009]

备注/Memo

备注/Memo:
-
更新日期/Last Update: 2016-10-31